Hoshizaki“A Superior Degreeof Reliability”www.hoshizaki.comModelsKM-1800SAH/3KM-1800SWH/3KM-1800SRH/3Stackable Crescent Cuber Hoshizaki America, Inc.I
10Note: When used with a storage bin not recommended by Hoshizaki, the icemaker needs the space at the bottom opening as in the illustration.Unit: inc
11Note: When used with a storage bin not recommended by Hoshizaki, the icemaker needs the space at the bottom opening as in the illustration.Unit: inc
123. KM-1800SRH/3Note: When used with a storage bin not recommended by Hoshizaki, the icemaker needs the space at the bottom opening as in the illustr
13II. Installation and Operating InstructionsA. Checks Before InstallationIMPORTANT1. Remove all shipping cartons, tape and packing. If packing materi
14C. LocationWARNINGThis icemaker is not intended for outdoor use. Normal operating ambient temperature should be within +45°F to +100°F (+7°C to +38°
15CAUTIONBefore operating the icemaker, the bin control thermostat assembly must be installed correctly. Failure to properly install the assembly coul
16If a Hoshizaki B-800, B-900 or B-1150 bin is being used:g. Put aside the "Z" bracket; it is not needed with the bins listed above.h. Remov
177) Remove the thermostat bulb attachment (plastic) of the upper unit from the thermostat extension bracket (stainless).8) Carefully remove the therm
18Fig. 8bF. Electrical ConnectionWARNING1. Electrical connection must be made in accordance with the instructions on a "WARNING" tag, provid
19G. Installation of Remote Condenser Unit1. Checks Before Installation1) Unpack and remove shipping carton, tape(s) and packing.2) Check that the ref
2IMPORTANTOnly qualified service technicians should attempt to install, service or maintain this icemaker. No installation, service or maintenance shou
203. Setup1) Secure the legs to the condenser unit with eight M8×16 mm hexagon bolts and M8 nuts as shown in the illustration. See Fig. 10.Note: Locat
214. Electrical ConnectionWARNINGThis remote condenser unit requires a ground that meets the national and local electrical code requirements. To preve
22H. Water Supply and Drain ConnectionsSee Fig. 14a, 14b and 14cWARNINGTo prevent damage to the pump assembly, do not operate the icemaker when the wa
23Fig. 14aKM-1800SAH/3KM-1800SWH/3Fig. 14b
24KM-1800SRH/3 Fig. 14c
25I. Final Checklist 1) Is the icemaker level?2) Is the icemaker in a site where the ambient temperature is within +45°F to +100°F (+7°C to +38°C) all
26J. StartupCAUTION1. All parts are factory-adjusted. Improper adjustments may result in failure.2. If the unit is turned off, wait for at least 3 min
27III. Cleaning and Maintenance InstructionsIMPORTANTEnsure all components, fasteners and thumbscrews are securely in place after any maintenance or c
281. Cleaning Procedure1) Dilute approximately 38 fl. oz. of recommended cleaner Hoshizaki "Scale Away" or "LIME-A-WAY," (Economics
2924) Turn on the power supply to rinse off the cleaning solution.25) Turn off the power supply after 5 minutes.26) Remove the front panel and the ins
3• Please review this manual. It should be read carefully before the icemaker is installed and operated. Only qualified service technicians should inst
302. Storage Bin and Scoop• Wash your hands before removing ice. Use the plastic scoop provided (bin accessory).• The storage bin is for ice use only.
312. Remove the water from the potable water supply line:1) Remove the front panel. (Except water-cooled model)2) Move the control switch on the contr
32HOSHIZAKI AMERICA, INC.618 Hwy. 74 S., Peachtree City, GA 30269 USA TEL (770) 487-2331 FAX (770) 487-3360 www.hoshizaki.com 91A1SA10D
4See the nameplate for electrical and refrigeration specifications. This nameplate is located on the upper right hand side of rear panel.Since this nam
5See the nameplate for electrical and refrigeration specifications. This nameplate is located on the upper right hand side of rear panel.Since this nam
6See the nameplate for electrical and refrigeration specifications. This nameplate is located on the upper right hand side of rear panel.Since this nam
7See the nameplate for electrical and refrigeration specifications. This nameplate is located on the upper right hand side of rear panel.Since this nam
8See the nameplate for electrical and refrigeration specifications. This nameplate is located on the upper right hand side of rear panel.Since this nam
9See the nameplate for electrical and refrigeration specifications. This nameplate is located on the upper right hand side of rear panel.Since this nam
Comments to this Manuals