Issued: 9-4-2008Revised: 2-5-2013Hoshizaki “A Superior Degree of Reliability” www.hoshizaki.com Models KM-1301SAH/3 KM-1301SWH/3 KM-1301SRH/3 Stackab
10Note: When used with a storage bin not recommended by Hoshizaki, the icemaker needs the space at the bottom opening as in the illustration.Unit: (mm
11Note: When used with a storage bin not recommended by Hoshizaki, the icemaker needs the space at the bottom opening as in the illustration.2. KM-130
123. KM-1301SRH/3Note: When used with a storage bin not recommended by Hoshizaki, the icemaker needs the space at the bottom opening as in the illustr
13II. Installation and Operating InstructionsA. Checks Before InstallationIMPORTANT1. Install in accordance with all applicable national, state, and l
14C. LocationCAUTION1. This icemaker is not intended for outdoor use. Normal operating ambient temperature should be within +45°F to +100°F (+7°C to +
156) Level the icemaker and storage bin in both the left-to-right and front-to-rear directions. Adjust the storage bin legs to make the icemaker level
16E. Installation of Second Unit1) See "II.D. Setup" for the lower unit installation.2) Remove the top panel and the top insulation of the l
177) Remove the tie securing the upper unit's bin control thermostat assembly.8) Remove the bin control thermostat assembly from the shipping hoo
18F. Electrical ConnectionWARNING1. Electrical connections must be made in accordance with the instructions on the "WARNING" tag, provided w
19G. Installation of Remote Condenser Unit1. Checks Before Installation1) Remove the shipping carton, tape, and packing material.2) Check that the ref
2IMPORTANTOnly qualied service technicians should attempt to install, service, or maintain this icemaker. No installation, service, or maintenance sh
204. Line Set•Prechargedtubingkits,availableasoptionalequipmentfromHoshizakiAmerica,arerecommended. Field fabricated line sets are allowed
21Factory Line Set Installation1) Route the factory line set (1/2" OD discharge line and 3/8" OD liquid line) from the remote condenser unit
225. Electrical ConnectionWARNING1. Electrical connections must meet national, state, and local electrical code requirements. Failure to meet these co
23H. Water Supply and Drain ConnectionsSee Fig. 14, 15, or 16CAUTION1. Normal operating water temperature should be within +45 F to +90 F (+7°C to +32
24•Condensationdrainoutletisa3/8"ODstainlesstube.Theicemakerandcondensationdrain line(s) must be run separately from the storage bi
25KM-1301SAH/3 KM-1301SRH/3Bin Drain Outlet 3/4" FPTIcemaker Water Supply Line Shut-Off ValveIcemaker Water Supply Line Drain ValveIcemaker Water
26Fig. 16KM-1301SWH/3Connection To A Potable Water SupplyCondenser Water Supply Inlet 1/2" FPTIcemaker Water Supply Inlet 1/2" FPTIcemaker D
27I. Final Checklist 1) Is the icemaker level?2) Is the icemaker in a site where the ambient temperature is within +45°F to +100°F (+7°C to +38°C) and
28J. StartupCAUTION1. All parts are factory-adjusted. Improper adjustments may result in failure.2. On remote air-cooled model, the icemaker should ha
29III. Cleaning and MaintenanceIMPORTANTEnsure all components, fasteners, and thumbscrews are securely in place after any cleaning or maintenance is d
3IMPORTANTThis manual should be read carefully before the icemaker is installed and operated. Only qualied service technicians should install, servic
301. Cleaning Procedure1) Dilute 27 . oz. (800 ml) of Hoshizaki "Scale Away" with 5 gal. (19 l) of warm water.2) Remove all ice from the ev
3121) Remove the front panel and fully open the cleaning valve.22) Move the control switch to the "WASH" position.23) Replace the front pane
32B. Maintenance InstructionsIMPORTANTThis icemaker must be maintained individually, referring to the instruction manual and labels provided with the
334) Attach a compressed air or carbon dioxide supply to the condenser water supply line drain valve.5) Open the water regulating valve by using a scr
34HOSHIZAKI AMERICA, INC.618 Hwy. 74 S., Peachtree City, GA 30269 USA TEL (770) 487-2331 FAX (770) 487-3360 www.hoshizaki.com 1A2910-010
4See the nameplate for electrical and refrigeration specications. This nameplate is located on the rear panel.Since this nameplate is located on the
5See the nameplate for electrical and refrigeration specications. This nameplate is located on the rear panel.Since this nameplate is located on the
6See the nameplate for electrical and refrigeration specications. This nameplate is located on the rear panel.Since this nameplate is located on the
7See the nameplate for electrical and refrigeration specications. This nameplate is located on the rear panel.Since this nameplate is located on the
8See the nameplate for electrical and refrigeration specications. This nameplate is located on the rear panel.Since this nameplate is located on the
96. KM-1301SRH3 (remote air-cooled)See the nameplate for electrical and refrigeration specications. This nameplate is located on the rear panel.Since
Comments to this Manuals