Hoshizaki“A Superior Degreeof Reliability”www.hoshizaki.comModelKMS-1400MLHIncludingCondensing Unit Model SRK-14H/3Modular Crescent Cuber Serenity Ser
10The condensing unit must be positioned in a permanent site under the following guidelines:• A rm and at site.• A dry and well ventilated area with
11B. Checks Before InstallationIMPORTANT1. Install in accordance with all applicable national, state, and local regulations.2. Remove the shipping car
122. Condensing Unit• Top Panel: Remove the screws and lift off.• Front Panel: Remove the screws and lift off.• Left Side/Rear Panel: Remove the screw
13D. Installation of the IcemakerCAUTION1. Power supply and ground wire to the icemaker are supplied from the condensing unit. For details, see sectio
14CAUTIONThe bin control lead is routed through the back of the icemaker. If care is not taken when removing the tank, the lead could be severed.6) Pu
15CAUTIONIf a gap is left between the bin control and the wall of the dispenser, ice may get between them and damage the bin control. Therefore, make
16E. Installation of the Condensing UnitCAUTION1. Failure to install the equipment within these guidelines may adversely affect performance, component
17Factory Line Set Installation1) Route the factory line set (5/8" OD suction line and a 1/2" OD liquid line) from the condensing unit to th
18F. Electrical ConnectionWARNING1. Electrical connections must be made in accordance with the instructions on the "WARNING" tag, provided w
192. Condensing Unit1) Connect the wire harness wires to the appropriate terminals on the condensing unit's terminal board using the wiring label
2IMPORTANTOnly qualied service technicians should attempt to install, service, or maintain this icemaker. No installation, service, or maintenance sh
20L2or L3 ContactorHGVLLVNeutralFuse 10ACBHGVLLVNeutralSRK Condensing UnitWire Harness ConnectionsBR VPBK WBRGNGNDVPBKWGNBRVP BKWGNBRV PBKWGNDLegend:G
21G. Water Supply and Drain Connections See Fig. 9IMPORTANTTo prevent damage to the equipment, do not operate the icemaker when the water supply is
22H. Final Checklist1) Is the icemaker level?2) Are all components, fasteners, and thumbscrews securely in place?3) Is there at least 24" (61 cm)
23I. StartupIMPORTANT1. Electrical power must be on at the condensing unit for a minimum of 4 hours prior to startup to prevent compressor damage.2. A
24III. Cleaning and Maintenance IMPORTANTEnsure all components, fasteners, and thumbscrews are securely in place after any cleaning or maintenance is
25e. Reassemble the oat switch. Replace the rubber boot and the oat switch in their correct positions. Reconnect the vent tube.f. Replace the right-
262. Sanitizing Procedure - Following Cleaning Procedure1) Dilute 2 . oz. (60 ml or 4 tbs) of a 5.25% sodium hypochlorite solution (chlorine bleach)
27C. Preparing the Icemaker for Long StorageCAUTIONWhen shutting off the icemaker for an extended time, drain out all water from the water tank and re
2815) Move the control switch to the "OFF" position. 16) Disconnect the oat switch vent hose from the drain hose tee. Move the service swit
29HOSHIZAKI AMERICA, INC.618 Hwy. 74 S., Peachtree City, GA 30269 USA TEL (770) 487-2331 FAX (770) 487-3360 www.hoshizaki.com 91A1YD10B
3CONTENTSI. Specications ... 4A. Na
4NOT INTENDED FOR OUTDOOR USE!WARNING: RISK OF ELECTRICAL SHOCK, WHICH CAN CAUSE INJURY OR DEATH. DISCONNECT ALL REMOTE ELECTRICAL POWER SUPPLIES BEFO
5FOR OUTDOOR USEMOTOR-COMPRESSOR THERMALLY PROTECTEDWARNING: RISK OF ELECTRICAL SHOCK, WHICH CAN CAUSE INJURY OR DEATH. DISCONNECT ALL REMOTE ELECTRIC
63. Condensing Unit Model SRK-14H3See the nameplate for electrical and refrigeration specications. This nameplate is located on the side panel.Note:
7B. Dimensions/Connections1. KMS-1400MLHUnit: mm [inches]
82. Condensing Unit Model SRK-14H/3Unit: mm [inches]Note: Legs are included with condensing unit. Leg height is 380 mm (14.96 in.).
9II. Installation and Operating Instructions IMPORTANT1. Install in accordance with all applicable national, state, and local regulations.2. Remove th
Comments to this Manuals